|
Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
|
Thread Tools | Search this Thread |
10-28-2020, 02:41 PM | #1 |
Undisputed El Presidente
Join Date: Jun 2012
Drives: Zenki 37J ZN6
Location: Stockton, CA
Posts: 11,571
Thanks: 9,382
Thanked 9,397 Times in 5,261 Posts
Mentioned: 374 Post(s)
Tagged: 33 Thread(s)
|
Rebuild with OEM short block
Has anyone done a rebuild after a spun bearing using an oem short block and their original heads?
I know people havent had great luck with built motors but wondering if anyone has gone the factory route |
10-28-2020, 02:58 PM | #2 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,202
Thanks: 18,252
Thanked 16,370 Times in 7,407 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
10-29-2020, 02:17 AM | #3 | |
CAD monkey
Join Date: Aug 2016
Drives: '15 GT86 Giallo - Supercharged
Location: Slovenia
Posts: 78
Thanks: 16
Thanked 66 Times in 36 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
MY15 engine, spun rod bearing on #1 rod. Rebuilt (heads re-surfaced and water blast cleaned) with a new 17+ factory short block, FA20DIT conrods and some other mods: https://www.ft86club.com/forums/show...&postcount=948 It's been 1 year since, 0 issues. Last edited by Boccaccio; 10-29-2020 at 04:16 AM. |
|
The Following User Says Thank You to Boccaccio For This Useful Post: | finch1750 (10-29-2020) |
11-17-2020, 11:56 AM | #4 |
Undisputed El Presidente
Join Date: Jun 2012
Drives: Zenki 37J ZN6
Location: Stockton, CA
Posts: 11,571
Thanks: 9,382
Thanked 9,397 Times in 5,261 Posts
Mentioned: 374 Post(s)
Tagged: 33 Thread(s)
|
Anyone else?
|
11-18-2020, 12:01 AM | #5 |
chicken tonight
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,944
Thanks: 52,291
Thanked 36,616 Times in 18,979 Posts
Mentioned: 1109 Post(s)
Tagged: 9 Thread(s)
|
@ermax
I'd do it in a heartbeat. Just takes patience and attention to detail. Lots of steps, each of them equally important. Can't rush it.
__________________
|
11-18-2020, 07:51 AM | #6 |
Senior Member
Join Date: Feb 2017
Drives: '13 Whiteout
Location: San Clemente
Posts: 1,491
Thanks: 496
Thanked 1,242 Times in 673 Posts
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
|
For the extra 1,400 I used an IAG short block. Better oiling and everything upgraded to handle in excess of 500 hp. Staying NA I have a lot of confidence now. Motor built by a top notch race shop. I do NOT want to go through the blown motor nightmare again!
|
11-25-2020, 05:03 PM | #7 | |
Senior Member
Join Date: Sep 2017
Drives: 2022 BRZ Limited Silver
Location: Jacksonville, FL
Posts: 2,532
Thanks: 882
Thanked 2,045 Times in 1,188 Posts
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
|
Rebuild with OEM short block
Quote:
I spun #3 and rebuilt at 89,964mi and now I'm at 120,686mi. I beat the living crap out of it and all is well. I burnt oil on the original engine but after the rebuild I don't burn a drop between changes. I subscribe to the hard break in which may have something to do with my lack of oil consumption. I did an OEM short block, new VVT filters and new injector seals. It's a bitch to get all the packing seal off everything (all total I probably have 24 hours just scraping off packing). I flushed a lot of water through the heads to be sure I got all the packing out of it or any bearing material. All total I had about $2500 in the job including oil and coolant. If it wasn't for the packing it's actually really easy to work on. You can pull the engine in no time and I didn't need a bunch of special tools. You also have to be really meticulous about applying the new packing seal. When doing the packing do not use the original service manual, use the instructions from the valve spring recall. They are WAY more detailed. Last edited by ermax; 11-25-2020 at 09:59 PM. |
|
The Following 3 Users Say Thank You to ermax For This Useful Post: |
11-25-2020, 05:25 PM | #8 |
chicken tonight
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,944
Thanks: 52,291
Thanked 36,616 Times in 18,979 Posts
Mentioned: 1109 Post(s)
Tagged: 9 Thread(s)
|
I think we'd do just fine working together on a project.
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Best CARB legal SC kit? Jackson? Oem reliable block rebuild? Cayman killer? | Yui-Chan | Forced Induction | 179 | 03-04-2015 07:50 PM |
For Sale: Frs long block 3 k miles NEED To Be Rebuild. Project | sokol | Engine, Exhaust, Bolt-Ons | 7 | 02-27-2015 12:10 AM |
WTB: FA20 Long Block/Short Block blown/running | The Racers Line | Engine, Exhaust, Bolt-Ons | 7 | 07-29-2014 01:26 AM |
WTB: FA20 Short Block or Blown Long Block | The Racers Line | Want-To-Buy Requests | 1 | 06-29-2014 05:21 PM |
WTB: short block or long block | DOTman05 | Engine, Exhaust, Bolt-Ons | 2 | 07-14-2013 06:48 AM |